Sloth

[RCcola55]

I think Chevy TBI actually runs at a higher pressure than the Ford injection, but I could be wrong.

you are wrong karl, you suck!!!!!

[KrazyKarl02]

you are wrong karl, you suck!!!!!

If anyone needs me, I will be in the corner crying. Clarke thinks I suck...

[RCcola55]

If anyone needs me, I will be in the corner crying. Clarke thinks I suck...

Ill make it up to you im sorry

[Sparling]

Ok, I am biting my tongue here, what I meant is that a ford efi setup will not be economically feasable because that would require efi heads, new fuel lines etc.

Yes tbi is fuel injection but I thought it was different being a low pressure system that injects from one place rather than injectors at each cylinder.

I didn't say anything about using ford ****. Did ford ever even make a M motor that was EFI?

[TdmayfieldIV]

I didn't say anything about using ford ****. Did ford ever even make a M motor that was EFI?

No

They didn't last long enough to see ford do efi

[JB]

I don't like this Rockwell idea. I think you should make this this a cruiser, ala, Less Nasty.

1) TBI, fix leaks, make drivetrain respectable.

2) Proper tire/lift. The truck looks too high for 35s. How much lift are you running? If 4", plus those nasty cut fenders, then it needs 37s. If it is 6", then you need 39-40" Sell those mud grapplers and buy something good. Level it out. Isn't it a little taller in the rear?

3)Keep 44/9". Or swap in a 10.25" and find some used 8 lug outers for the 44.

4)Remove that super ****ing gay prerunner bar and throw it in the trash.

5)Find a DD.

[TdmayfieldIV]

I don't like this Rockwell idea. I think you should make this this a cruiser, ala, Less Nasty.

1) TBI, fix leaks, make drivetrain respectable.

2) Proper tire/lift. The truck looks too high for 35s. How much lift are you running? If 4", plus those nasty cut fenders, then it needs 37s. If it is 6", then you need 39-40" Sell those mud grapplers and buy something good. Level it out. Isn't it a little taller in the rear?

3)Keep 44/9". Or swap in a 10.25" and find some used 8 lug outers for the 44.

4)Remove that super ****ing gay prerunner bar and throw it in the trash.

5)Find a DD.

1. leaks are fixed but it needs tranny work
2. its a 4" lift
3. Why not 1 tons
4. NO
5. Check, already got one

[stx4wheeler]

I'm about 99% sure that you cannot swap efi heads and intake onto an m block. The only way you can do efi is to build a custom intake with injectors in it like Jopes and a couple others of Fsb have done or go tbi/projection(crap).

Ok, I am biting my tongue here, what I meant is that a ford efi setup will not be economically feasable because that would require efi heads, new fuel lines etc. .

[uglyota]

injects. fuel. according to an electronic trigger.

google TPI, MPFI, CPI...and TBI

[agjohn02]

injects. fuel. according to an electronic trigger.

google TPI, MPFI, CPI...and TBI

DI

[robertf03]

Hot Beef

[mudtoy67]

Hot Beef

You got a table for that?

[uglyota]

you loose!

[agjohn02]

you loose!

you're smarter than that right? is there a joke im missing there?

[TdmayfieldIV]

This thread has gone to ****! One noob comment and i am getting torched